myLargescale.com > Community > Forums - Reply to Topic

Thread: Reverse loop w/ LGB 10151 help please Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the myLargescale.com > Community > Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-30-2020 08:19 PM
kormsen
Quote:
Originally Posted by MattSF3 View Post
...
Is the diode so delicate that I may have fried it somehow? Are they replaceable? Is there a good way to test them?

Thanks!
they are not delicate and they are replacable.

if you got the same problem with new ones, probably you installed something wrong.
try to change around the wires, that go from transformer/controller to the rails. (on LGB the blue and red ones)
07-30-2020 06:45 AM
Dan Pierce I find Martin to have some great diagrams for the older LGB EPL system. Look at this link for a dogbone setup.



http://www.altek.nl/graphtips/keerlussen.gif
07-30-2020 12:49 AM
MattSF3 I've used 3 different K sections, all brand new out of the box, and have had the same problem with all of them.

Is the diode so delicate that I may have fried it somehow? Are they replaceable? Is there a good way to test them?

Thanks!
07-29-2020 07:01 PM
kormsen look it up in the http://kormsen.info/lgb-manual.pdf pages 122 and 123.

maybe, the previous owner messed with the diodes in the "K" unit.
07-28-2020 11:36 PM
MattSF3
Thanks

Thanks All,

I'm running DC. Right now I was just trying to go super simple and was just using an LGB 5003, almost like I was just doing a basic loop. I have a LGB 5006 that I planned on using on the final setup.

Thanks for the reference to 559. That was new to me, and definitely looks like it will help. What I was trying for now is basically Circuit 8 (p 122-123), which seems to show a simple set up with the connections outside the loop, and T/K in the loop, no other wiring. Is this right? Because that is how I have mine (as far as I can tell)...

I have EPL switches and all that stuff, that was Phase 2. I was pretty much just making sure that I was ok on clearances, bridges etc before I got in too deep (or deeper I guess).

Thanks!
07-28-2020 01:57 PM
toddalin Are you using a/c or d/c to power the turnout motors/related parts? You should be using an a/c supply of about 16 volts and the LGB parts convert this to the proper d/c polarity.
07-28-2020 08:36 AM
krs For DC, did you follow the wiring in the attached pdf?
For this LGB reverse loop, the trains MUST always run around the reverse loop only in the direction indicated by the red arrows
http://www.gbdb.info/data/weitere_do...GB/1015K_2.pdf
07-28-2020 07:35 AM
Dan Pierce Are you DC or DCC?
Did you ad a DPDT switch to reverse the mainline power after entering the loop?
For DC see page 124 of the LGB 559 PDF manual, it is available on the web via a goodle search.
07-28-2020 12:25 AM
MattSF3
Reverse loop w/ LGB 10151 help please

It's a long story, but I recently inherited ALOT of G scale trains and thought it would be nice to add a small loop in the garden. That loop has qickly turned into a large layout with a reverse loop at each end. I finally got the track set and leveled so I figured I'd give it a test run, and had problems with both loops.

When the loco enters the loop and crosses the 1015T section it dies, as if there is no power. This happens at both loops. I was worried that maybe they were old or damaged, so I repalced one with a brand new one and it didn't work either. I tried flipping the T section just incase, but nothing. The K section has the arrow pointing out of the loop, towards the switch as indicated in the instructions.

Is there something that I'm missing, or an easy diagnostic? If it matters, I'm using a cheap Playmobile loco now, since the track is still in construction mode and I didn't want to bring out the good stuff quite yet. I have LGB locos to use if it matters.

THANK YOU!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Powered by vBadvanced CMPS v3.2.3

All times are GMT -4. The time now is 02:50 PM.



Powered by vBulletin® Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.6.1
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.